Reasons Your fiat 124 spider key fob not working 500 Key Fob Won't Work

A key fob for the fiat 500 key fob reset 500 allows you to easily open doors and start your vehicle. However, there are many reasons why the fob won't be functioning. These include a dead battery, water damage, receiver module issues, and interfering.

This listing is for an NEW replacement fiat key fobs Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local automotive locksmiths). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob won't function is due to the battery is dead. Modern key fobs have limited operating range and must be within only a few inches from the vehicle to function. If you are further away from your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at your local hardware store, or on the internet.

After you've changed the battery on the coin cell, you can test it by standing in front of your fiat 124 spider key fob Cover 500 and pressing the buttons. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the key fob won't work after replacing the battery, it might have water damage that prevents it from connecting to the receiver module in your car. Water damage can happen in a number of ways, ranging from small splashes to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture back out. If this doesn't work your fob is likely to require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

Damage to the water supply can occur if you submerge the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to become shorted and eventually cease to function. If you get the fob wet, it's not an ideal choice, but if you drop it into the water in a cup or do not remember to take it out of your pants pocket before running the washing machine Don't give up hope.

First, remove the battery. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it completely before replacing the battery. Check the fob again to verify if it's working. If the key still doesn't work, it might need to be reset. This is usually handled by an auto locksmith or dealer.

If your key is older and not programmed for your vehicle You will need to replace it completely. This is a simple process that can be handled by a professional automotive locksmith. The locksmith will need to cut the key to match the ignition on your vehicle. The locksmith will also need to program your fob into the car's system. It's a simple and inexpensive process that can be completed in the next day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote typically has an area of 30 feet or less, and if it's too far away from your car it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If your fob won't work after replacing the coin battery, also called a "button", "watch" or "button" It may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob will fix the issue. The instructions are available for most vehicles on YouTube or in the owner's manual.

It is possible to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension it could prevent the coin battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software issues or hardware issues. This could cause a significant problem, but you can usually fix it by visiting an auto locksmith to reprogram your fob. In some cases, they may need to reinstall the software on your body control module too.

Interference

In addition to a dead coin battery The key fob may not be able to transmit or receive a signal due to interference. This could occur if the key fob is in proximity to an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob might not work due to a bad connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. You could have a malfunctioning fiat 500 key fob reset receiver module after you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then translated by the vehicle.

There is a straightforward method to reset the 500's onboard system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any residual electricity and restart the fiat punto car key replacement's computers, which could allow you to get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to determine the root cause of any problems.